Hi, This is POPOKURO! This time, using 100-yen materials, I made glittering water domes! Use “dome ornament kit” purchased from Seria It is a set of only dome and pedestal How to make is written in the manual inside 😊 IIt is necessary to pay attention to the type of the adhesive This is a black type pedestal This is a white type pedestal This is a mascot of Rody purchased from Seria ❤ There are many color variations It is cute with a package like sweets 😊 Glue the mascot to the pedestal using the LED-UV resin Curing time is 2~3 minutes with UV-LED light 3~5 minutes with UV light 3~15 minutes by sunlight Put resin on pallet Plenty of resin on Rody’s feet Place it on the pedestal Cure for about 5 minutes with UV-LED light This seems to be hard to penetrate light so apply it longer and harden it firmly File the adhesive surface of the domee while curing I thought it is hard to stick if it is slippery… I bought this file from Daiso If you’ve done, wipe off the powder The mascot was fixed to the pedestal Before placing the dome on the pedestal, put the glitter on it. The case of small glitters, you can put them into the dome through the hole of the pedestal later Decorative Nail Parts (Crystallized hologram) from DAISO Use silver-colored random shapes Decorative Nail Parts (Twinkle) from DAISO Use golden ✨ shape and pink heart shape Decorative Nail Parts (3D Jewel) from DAISO Use white Place glitter near the center of the pedestal Crystallized hologram Heart shape ✨ shape 3D jewel Crystallized hologram added Move the glitter near the edge to the middle Put the resin on the edge of the pedestal 3x speed If there are gaps between the dome and the pedestal, water will leak, so make sure there ’s no gap Put on the dome Press tightly so that there is no gap Pre-curing by applying UV-LED light for about 30 seconds while holding it tight Apply UV-LED light for about 5 minutes to fully cure Cured Let’s pour water into the dome! Purified water Use a squeeze bottle to pour water because the hole of the pedestal is small Cut the nozzle Put purified water in the bottle Pour through the holes of the pedestal Glitter doesn’t dance with water alone … Add detergents that contain surfactants It’s okay with small amount Glitter is dancing! There is still air in the water … Fill a large bowl with water to remove air bubbles I put the tap water in the bowl Adjust the angle so that air bubbles can escape from the holes in the pedestal When the air bubbles are completely removed, put a rubber stopper in the dome hole in the water The bubbles are gone 😊 Bubbles are generated again…! There is a gap between the dome and the pedestal💦 I will fill the gap with resin Wipe the dome well and put the resin on the gap Cure Irradiate UV-LED light for 5 minutes with resin coated side up The gap seems to be filled. Remove air bubbles again Bubbles are gone 😊 As time goes on, bubbles attached to the mascot etc. float up, so it is better to remove the bubbles again Next, decorate the pedestal and finish Use decoration sticker The color is pop and cute 😊 done! Rody’s sparkling dome has been completed! I made this with a transparent Rody This is a blue Rody It is fun to make it with your favorite mascot ♪ If the material does not transmit light, it cannot be bonded with UV resin Glue to the pedestal with a water-resistant adhesive This is made without using resin I will introduce how to make it for reference Glue with silicone repairing agent instead of resin Because it is white, it also expresses the accumulated snow snowhouse snowman Cut and use the rest of the tree used in the previous video Cut to size you like with nippers Shape the tree with scissors Remove the chips Apply the silicone to the entire pedestal Be careful not to fill the hole and extend with a spatula Apply carefully so that there is no gap at the end When finished, place the ornaments If silicone is not enough, add Put snow powder in the inverted dome Turn the pedestal upside down and cover it tightly Fix it with masking tape and dry it upside down for one day. Once completely dry, add water and detergent as with Rody’s dome and remove any air bubbles I decorated the pedestal with this decorative tape The snow globe of the snowman was completed! Thank you for watching to the end!